How to Contribute a C-Kermit Binary

`How to Contribute a C-Kermit Binary`

[ Unix ] [ VMS ] [ Other ]

Unix

Check the binaries table to make sure the binary you are about to make is not already there, or is not at the current C-Kermit release level (i.e. 8.0.209).
Make a fresh directory and 'cd' to it. Example:
```
  $ mkdir kermit
  $ cd kermit
```

Download the appropriate source code archive. Click on the download link or do it by hand the old-fashioned way. Example:

  $ ftp kermit.columbia.edu
  User: anonymous
  Password: olga@xyzcorp.com
  ftp> cd kermit/archives
  ftp> binary
  ftp> get cku209.tar.gz
  ftp> bye
  $

Alternatively, if you have a fairly recent Kermit client (C-Kermit 7.0 or later, or K95 1.1.20), you can download the archive with Kermit itself, from the Kermit Project's Internet Kermit Service:

  $ kermit
  C-Kermit> iksd /user:anonymous kermit.columbia.edu
  Enter e-mail address as Password: olga@xyzcorp.com
  (/) IKSD> send kermit/archives/cku209.tar.gz
  (/) IKSD> exit
  C-Kermit> exit
  $

If you downloaded a compressed tar file, uncompress it. Examples:
```
  $ gunzip cku209.tar.gz
  $ uncompress cku209.tar.Z
```
If you downloaded a tar archive, "un-tar" it. Example:
```
  $ tar xvf cku209.tar
```
If you downloaded a Zip archive, unzip it. Example:
```
  $ unzip -a cku209.zip
```

Now you can delete the tar archive (or zip archive) if you wish:

  $ rm cku209.tar                 (or rm cku209.zip)

Read the comments at the top of the makefile to find out which target is appropriate for your computer and operating system, and then give the appropriate "make" command. Examples:

  $ make linux                    (Linux, almost any version)
  $ make freebsd44                (FreeBSD 4.4)
  $ make solaris8                 (Solaris 8 with cc)
  $ make solaris8g                (Solaris 8 with gcc)
  $ make irix62                   (IRIX 6.2)

Rename (or copy, or link) the resulting "wermit" binary to match the naming conventions in the C-Kermit binaries table. In most cases, this would be:

  cku209.makefiletarget-architecture-osversion

Examples:

  cku209.linux-alpha-db2.2        (Debian Linux 2.2 on the Alpha)
  cku209.linux-i386-db2.2         (Debian Linux 2.2 on a PC)
  cku209.solaris25-i386-2.5.1     (Solaris 2.5.1 on a PC)
  cku209.solaris25-sparc-2.5.1    (Solaris 2.5.1 on a Sun)
  cku209.solaris25g-sparc-2.5.1   (Ditto but built with gcc)

For some platforms, additional information must be included in the name. For Silicon Graphics IRIX, for example, we need the Instruction Set Architecture (MIPS level) and the Application Binary Interface:

  cku209.irix53-mips2-o32-5.3
  cku209.irix65-mips3-n32-6.5.14m

If you want to make another binary, use the "clean" target to remove the object files:
```
  $ make clean
```
and then go back to step 7.

Upload the binary (or binaries) you have built to ftp://kermit.columbia.edu/kermit/incoming/. You can use FTP or Kermit. Example:

  $ cp wermit cku209.irix62-mips3-n32.6.2
  $ ftp kermit.columbia.edu
  User: anonymous
  Password: olga@xyzcorp.com
  ftp> cd kermit/incoming
  ftp> binary
  ftp> put cku209.irix62-mips3-n32.6.2
  ftp> bye
  $

If you compress the binary, be sure to include the appropriate compression suffix (.Z or .gz) in the filename. Example:

  $ cp wermit cku209.irix62-mips3-n32.6.2
  $ gzip cku209.irix62-mips3-n32.6.2
  $ ftp kermit.columbia.edu
  User: anonymous
  Password: olga@xyzcorp.com
  ftp> cd kermit/incoming
  ftp> binary
  ftp> put cku209.irix62-mips3-n32.6.2,gz
  ftp> bye
  $

Send e-mail to kermit@columbia.edu and let us know that you uploaded a binary and give any relevant information: machine/OS model and particulars, any error messages or warnings, any changes you had to make to the build procedure or source code.
To install the version of Kermit you have just built, read the installation instructions.

Thanks!

VMS

Check the binaries table to make sure the binary you are about to make is not already there, or is not at the current C-Kermit release level (i.e. 8.0.209).

Make a fresh directory and SET DEFAULT to it. Example:

  $ create/directory kermit
  $ set default [.kermit]

Download the VMS source code Zip archive. Click on the download link or do it by hand the old-fashioned way. Example:

  $ ftp kermit.columbia.edu
  User: anonymous
  Password: olga@xyzcorp.com
  ftp> cd kermit/archives
  ftp> binary
  ftp> get ckv209.zip
  ftp> bye
  $

Or use the Internet Kermit service as described above.

Unpack the Zip archive. Example:
```
  $ unzip -a ckv209.zip
```
Run the build procedure to make a "no-net" version (i.e. a version that does not have TCP/IP networking built in:
```
  $ @ckvker n
```
If you have a pre-5.0 VMS release, use the "old" build procedure:
```
  $ @ckvold n
```
If you experience any trouble, read the comments at the top of the build procedure.
Rename the resulting WERMIT.EXE binary to match the naming conventions in the C-Kermit binaries table:
```
  ckv209-architecture-vmsNN-nonet.exe
```
where architecture is "vax" or "axp" (or maybe by the time you read this, "ia64"); NN is the VMS version number, such as "72" for 7.2, and "nonet" means no networking. Examples:
```
  ckv209-vax-vms47-nonet.exe
  ckv209-axp-vms62-nonet.exe
```
If you have a TCP/IP product installed, create a second binary with TCP/IP networking built in:
```
  $ @ckvker
```
(or @ckvold for VMS 4.x or ealier).
Rename the second WERMIT.EXE binary like the first one, except this time include the TCP/IP product and version:
```
  ckv209-architecture-vmsNN-netVV.exe
```
where netVV is a three-letter code for the network product and its two-digit version number (with no decimal point):
  ucx  DEC TCP/IP
  tgv  TGV MultiNet
  pst  Process Software TCPware
  twg  The Wollongong Group WIN/TCP or PathWay
  cmu  Carnegie-Mellon University CMU/IP
Examples:
```
  ckv209-vax-vms55-ucx20.exe
  ckv209-axp-vms62-tgv41.exe
  ckv209-axp-vms73-ucx51.exe
```
If you want to make more binaries, use the build procedure's "c" option to remove the object files:
```
  $ @ckvker c
```
and then go back to step 5.

Upload the binary (or binaries) you have built to ftp://kermit.columbia.edu/kermit/incoming/. You can use FTP or Kermit. Example:

  $ ftp kermit.columbia.edu
  User: anonymous
  Password: olga@xyzcorp.com
  FTP> cd kermit/incoming
  FTP> binary
  FTP> mput ckv209*.exe
  FTP> bye
  $

Send e-mail to kermit@columbia.edu and let us know that you uploaded a binary and give any relevant information: machine/OS model and particulars, any error messages or warnings, any changes you had to make to the build procedure or source code.
To install the version of Kermit you have just built, read the installation instructions.

Thanks!

Other

[ Top ] [ C-Kermit Home ] [ Kermit Home ]

C-Kermit 8.0 / Columbia University / kermit@columbia.edu / 17 March 2003